ULN2803 Stepper Motor Driver Board For Arduino SCM
Specification:
- Size: 52 x 39mm
- Ports: Digita
- Chip: ULN2803 (contains 8 channel Darlington transistor drive)
- Drive voltage: 5V (recommended) 7-24V (via jumper switch, only external power supply)
- Output current: 500mA (total current)
- Can be driven 8 channel low level equipment or two five-pin stepper motor
- v Platform: Arduino, MCU
Feature:
- Use ULN2803, can drive 8 channel low level equipment
- Allows Arduino direct drive relay via low level, such as 12V LED lights strip, stepper motor
- Onboard voltage input jumper, can be directly used Arduino-powered, can also be driven by an external power supply
- You can directly drive 8 relays or 8 channel 12V LED lights strip
- Inputs use Arduino 3P interface can be directly connected to the sensor board
- Completely replace the 7 channle output ULN2003 drive plate, directly compatible
10-50V 40A DC Motor Speed Controller PWM Voltage Regulator Switch PCBA
Description:
- Working Voltage:10-50VDC
- Maximum Output Current:40A
- Maximum Output Wattage:2000W
- Control Motor Power :0.01-2000W
- Regulation range:5-100%
- Case Size:Approx.4.13''X2.17''X1.57''/10.5*5.5*4cm
5V Stepper Motor 28BYJ-48 With Drive Test Module Board ULN20
Product description:
It is 5V 4 phase Stepper Motor + Driver Board ULN2003 for ARDUINO.
5 Line 4 phase can be driven by ordinary uln2003 chip, can also be connected in phase 2 Stepper motor driver board with ULN2003
Stepper motor with a standard interface, directly plugable
A, B, C, D four-phase LED indicates the status of the stepper motor work
Household intelligent control
It Uses ULN2003 drive chip,500mA
L9110 - 2 DC Motor Driver Board
Product description:
L9110 - 2 DC Motor Driver Board
ULN2003 - Stepper Motor Driver Board
Product description:
ULN2003 - Stepper Motor Driver Board
L298 - Motor Control Driver Board
Product description:
L298 - Motor Control Driver Board
L9110 2-Channel Motor Driver Module - Red + Green (2.5~12V)
Product description:
Brand N/A
Model L9110
Quantity 1
Color Red + green
Material PCB + plastic + iron
Features Module description: Double L9110S chip motor drive; Module supply voltage: 2.5~12V; Suitable motor: the motor operating voltage between 2.5V~12V, the maximum operating current of 0.8A; Can drive two DC motors, or a 4-wire 2-phase stepping motor; PCB board size: 2.8cm x 2.1cm, compact size, easy for assembly; Provides with a fixed mounting hole, diameter: 3mm; Module interface specification: The 6-pin black curved pin description: VCC: external 2.5V~12V voltage; GND: external GND; The IA1: external microcontroller IO port; The IB1: external microcontroller IO port; IA2: external in microcontroller IO port; IB2: external microcontroller IO port; 4-pin green terminal description: OA1 / OB1 connect to DC motor 2-pin, no direction; OA2 / OB2 connects to DC motor 2-pin, no direction; Module for use: VCC and GND module power indicator light is on; IA1 input high, IA1 input low, (OA1 OB1) motor is transferred; IA1 input low, IA1 high level input, (OA1 OB1) motor reversal; IA2 input high, IA2 input low, (OA2 Ob2) motor is transferred; IA2 input low, IA2 input high, (OA2 Ob2) of motor reversal
Specification 2.5~12V
Application All kinds of electronic products or DIY lover
Other On-board ULN2003A chipset; 5~12V power supply; On-board 4-way indicator light; On-board XH-5P socket; Compatible with Arduino
English Manual/Spec Yes
Packing List 1 x Motor driver module
L293D - Motor Control Driver Board
Product description:
L293D - Motor Control Driver Board
Features & Specifications:
- Onboard L293D
- Screw Terminals for I/O connections
- Onboard 5V Regulator LM7805
- Output Current - 600mA per channel
- Easy interface with development boards
Digital Multi Servo Tester Module
Product description:
Digital Multi Servo Tester Module
Features & Specifications:
- There are 3 modes to check servos or ESC:
- Manual mode: Turn the knob to operate the servo.
- Neutral mode: Makes the servo go back to the neutral point.
- Automatic "window wiper" mode: Rotates the servo between maximum angles
- The device also can be used as a signal generator for electric speed controller (ESC).
- Supply Voltage - 4.8 to 6V DC
- Size: 48 x 42 x 17mm
Motor Drive Module -50 Amps
Product description:
Motor Drive Module - 50 Amps
Features & Specifications:
- Dual H bridge configuration
- Peak current- 50A
- Recommend max working current(Load): 20A
- Power VCC (Load): 0V~30V
- Recommend power vcc(load) : 12V ~ 26V
- Control VCC: 4V~12V
Note:Power VCC is recommended to be higher than 12V for large-current devices.
VNH2SP30 Stepper Motor Driver Module
Product description:
VNH2SP30 - Stepper Motor Driver Module
Features & Specifications:
- Voltage max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown
Easy Motor Driver
Product description:
Easy Motor Driver
Features & Specifications:
- A3967 microstepping driver
- MS1 and MS2 pins broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth)
- Compatible with 4, 6, and 8 wire stepper motors of any voltage
- Adjustable current control from 150mA/phase to 750mA/phase
- Power supply range from 7V to 30V. The higher the voltage, the higher the torque at high speeds
DKC-S100 length stepper motor controller
Product description:
DKC-S100 length stepper motor controller
Features & Specifications:
- 5V + VCC connected drive controller
- Pulse then drive controller CLK or PUL
- Then the direction of the drive controller DIR
- ENA is not connected drives
- The controller 's power V + drives connected to +24 V
- Power V- connected drive controller GND
- Wide input voltage : DC6-32V
- Multiple protection features : There are reverse polarity protection , overvoltage protection, overcurrent protection
- simple operation : no need to learn complicated programming commands , you can simply set the precise positioning
- Acceleration: Optimized S -type acceleration 0-20 files can be set .
- Display: 4 digital display the current operating state , the trigger number of pulses
- Output frequency: 35KHz maximum output pulse frequency .
- Input and output : non-isolated input and output . The bottom level of the input signal is valid.
- Dimensions : 80X42X24 ( mm ) standard face frame size
- Hole Size : 77X40 ( mm )
Forward, reverse , when the origin of the trigger with the drive 's power V- alone connection , the corresponding feature works DKC-S100 is independently developed by the company of a fixed-length type stepping motor controller. The controller uses the original imported high-speed smart chip as the hardware platform , the software uses a unique anti-jamming technology allows the controller's stability , reliability and strong anti-interference are very good . Therefore, the controller for harsh environmental factory floor . Can be applied to a variety of station control , fixed length control , precise control and other requirements .
PWM Based DC motor speed controller - 12V / 10A
Product description:
PWM Based DC motor speed controller - 12V / 10A
Features & Specifications:
- Control the speed of a DC motor with this controller.
- High efficiency, high torque, low heat generating.
- With reverse polarity protection, high current protection.
- Working Voltage: DC 12V - DC 40V.
- Control Power:0.01 - 400W.
- Static Current:0.02 A ( Standby ).
- PWM Duty Cycle:10% -100%.
- PWM Frequency:13 KHz.
- Material: Plastic, metal.
- Size:6cm x 7.5cm x 2.8cm
- Weight: 70g
PWM Based DC motor speed controller - 12V / 3A
Product description:
PWM Based DC motor speed controller - 12V / 3A
This DC Motor Speed Controller allows controlling the direction of a DC motor using a Pulse-Width-Modulated (PWM) DC voltage with a Duty Cycle fully adjustable from 0%-100%.
The motor speed controller can easily provide a continuous current of 3A to your DC motor or other DC load.
Features & Specifications:
- Input supply voltage:6V-28VDC
- The maximum output power: 80W
- The maximum continuous output current :3A
- Duty Cycle adjustable:0%-100%
Industrial DKC-1A stepper motor controller
Product description:
Industrial DKC-1A stepper motor controller
Features & Specifications:
- Wide voltage input: 5-32VDC;
- With a power anti-reverse polarity protection, overvoltage protection, overcurrent protection, complete protection of the safety controller
- Signal input to the bottom level of the input;
- Optimization of S-type acceleration curve
- Maximum output frequency up to 20K
- All input and output optocoupler isolation
- Board plant potentiometer speed control, external potentiometer speed automatic switching
- A variety of functions, set up a simple, functional and practical, Volume 5 * 8.2CM
Function modes
1: Automatic mode and from the
2: Single Entry Mode
3: One-Shot mode
4: Jog mode
A4988 Stepper Motor Driver Module
Product description:
A4988 Stepper Motor Driver Module
DRV8825 Stepper Motor Driver Module
Product description:
DRV8825 Stepper Motor Driver Module
TB6560 Stepper Motor Driver Controller Board
Product description:
TB6560 Stepper Motor Driver Controller Board
Features & Specifications:
- Working voltage DC 10V-35V. Recommended to use a switching 24VDC power supply.
- 6N137 high-speed optical coupling, guarantee high speed without losing step.
- Uses the TB6560AHQ chip with low voltage shutdown, overheating stop and overcurrent protection circuit to ensure optimal performance.
- Rated maximum output:3A, peak 3.5A.(Recomended 3A)
- For two-phase within 42,57 stepping 3A / four-phase / of line four / six-wire stepper motor,
- Automatic half current function.
- Subdivision: whole step, half-step, step 1/8, 1/16 step, a maximum of 16 subdivisions.
- Size:75 x 50 x 33mm
- Package weight:93g
Stepper Motor Driver Board ULN2003 for (For Arduino) 4-phase 5-line
Product description:
ULN2003 stepper motor driver board
Rated Voltage: DC 5V-12V
4-phase
Board Size: Approx. 40.5×21.3 mm
On-board XH-5 P socket.connect 28BYJ-48 Stepper Motor direct.
ULN2003 Stepper Motor Driver Module
Product description:
On-board ULN2003A chipset
5-12V power supply
On-board 4-way indicator light;
On-board XH-5P socket
Compatible with Arduino
Stepper Motor Driver Test and DIY
Product Type :Stepper Motor Driver Module
Package Type :OEM
Depth :6.2 mm
Height :35 mm
Width :30.5 mm
Product Weight :6.9 g
SKU:1451625