Ocean College and School Students Science Projects materials

CC3000 WIFI ARDUINO UNO

DESCRIPTION

High quality. The CC3000 hits that sweet spot of usability, price and capability. It uses SPI for communication (not UART!) so you can push data as fast as you want or as slow as you want. It has a proper interrupt system with IRQ pin so you can have asynchronous connections. It supports 802.11b/g, open/WEP/WPA/WPA2 security, TKIP & AES. A built in TCP/IP stack with a "BSD socket" interface. TCP and UDP in both client and server mode, up to 4 concurrent sockets. It does not support "AP" mode, it can connect to an access point but it cannot be an access point.

FEATURE

We wrapped these little silver modules in a tidy breakout board. It has an onboard 3.3V regulator that can handle the 350mA peak current, and a level shifter to allow 3 or 5V logic level. The antenna layout is identical to TI's suggested layout and we're using the same components, trace arrangement, and antenna so the board maintains its FCC emitter compliance (you'll still need to perform FCC validation for a finished product, but the Wi-Fi part is taken care of). Even though it's got an onboard antenna we were pretty surprised at the range, as good as a Smartphone’s.

IOT MODEM SIM800A BASED

LED INDICATIONS

The Network LED indicates the various status of GSM module eg. Power on, Network registration & GPRS connectivity. When the modem is powered up, this NETWORK LED will blink every second. After the Modem registers in the network (takes between 10-60 seconds), this LED will blink in step of 3 seconds. At this stage you can start using Modem for your application, showing that modem is registered with the network.

IOT MODEM SIM808A BASED

Wireless LIFI Module

PRODUCT NAME:LIFI & PRODUCT DEDSCRIPTION:

At the heart of this technology, a new generation of high-brightness light-emitting diodes. Very simply, if the LED is ON, user can transmit a digital string of 1, if it’s OFF then user can transmit a string of 0. It can be switched ON and OFF very quickly, which gives instant opportunity for transmitting data. It is possible to encode data in the light by varying the rate at which the LEDs flicker ON and OFF to pass different strings of 1s and 0s. The modulation is so fast that the human eye doesn’t notice. There are over 14 billion light bulbs used across the world, which needs to be replaced with LEDs ones that transmit data.

XBee 2mW Wire Antenna - Series 2 (ZigBee Mesh)

This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh

RF ASK module Wireless Transmitter + Receiver Pair 433 / 434 MHz

Applications - Remote Controls Automation System Wireless Security System Sensor Reporting Car Security System Remote Keyless Entry Supports All Wireless Applications using 8051/AVR/PIC/ARM Microcontrollers (Using HT12E - HT12D Pair)

GSM Module SIM800 Quadband

SIM800 is a complete Quad-band GSM/GPRS solution in a LGA type which can be embedded in the customer applications. SIM800H support Quad-band 850/900/1800/1900MHz, it can transmit Voice, SMS and data information with low power consumption. With tiny size of 15.8*17.8*2.4 mm, it can fit into slim and compact demands of customer design. Featuring and Embedded AT, it allows total cost savings and fast time-to-market for customer applications.

SIM900A GSM MODEM MODULE with SMA ANTENNA - CALL SMS GPRS with RS232, TTL & I2C

SIM900A Modem is built with Dual Band GSM/GPRS based SIM900A modem from SIMCOM. It works on frequencies 900/ 1800 MHz. SIM900A can search these two bands automatically. The frequency bands can also be set by AT Commands. The baud rate is configurable from 1200-115200 through AT command. The GSM/GPRS Modem is having internal TCP/IP stack to enable you to connect with internet via GPRS.

HC-05 Wireless Bluetooth RF Transceiver Module Serial/TTL/RS232

This module can be set to a transmitter or receiver, transmitter could pairing with receiver, receiver and receiver or transmitter and transmitter can't communication between, receiver could pairing with computers and cell phone bluetooth, when buying, the default for receiver. *support Master and Slave mode, modify by AT commander Product Description - The Bluetooth UART RS232 serial Converter Module can easily transfer the UART data through the wireless Bluetooth,without complex PCB layout or deep knowledge in the Bluetooth software stack, you can combine this bluetooth module with your system: MCU, ARM or DSP systems. GPS navigation system Water and electricity gas meter reading system SOC systems. Personal Digital Assistants (PDAs) Computer Accessories Other systems your want to use under bluetooth functions.

UART to WIFI Wireless Module Ethernet to WIFI Wireless HLK-RM04 with Antenna

Support the AP (wireless access point), the Client (Client), the Repeater (wireless relay), Bridge (wireless Bridge), the Router (wireless Router) five working mode AP mode - the default work mode. This mode device is a wireless access point, support plug and play, no configuration. The Router mode - this mode device is equivalent to a wireless Router, the wired interface as the WAN, the wireless LAN. Multiple wireless clients can share a broadband link on the Internet. Repeater mode, use of equipment of the wireless relay function, realizes the wireless signal relay and amplified, and form a new wireless coverage area, finally achieve the goal of extending wireless network coverage. Bridge model, use of equipment of Bridge function, first RM04 set up a wireless connection with the front end of wireless network, a wireless signals, and then itself to form a new wireless coverage, can effectively solve the problem of weak signal and signal blind spots, such as wireless coverage. Client work mode - in this mode the AP for the AP is wireless Client, equivalent to a wireless network card.

XBee / ZigBee Adapter board with USB interface

This is a simple to use, USB to serial base unit for the XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach USB cable, and you will have direct access to the serial and programming pins on the XBee unit. The board is powered by the USB cable.XBee modules and USB cable are sold separately. Features: • USB Connectivity • USB Powered. • Small footprint. • All XBee pins broken out. • Reset button • Onboard 3.3V regulated supply. • Small footprint.

SIM900A DUAL BAND GSM MODEM MODULE CHIP IC for CALL SMS GPRS FAX facility

The SIM900A is an ultra compact and reliable wireless module. The SIM900A is a complete Dual-band GSM/GPRS solution in a SMT module which can be embedded in the customer applications allowing you to benefit from small dimensions and cost-effective solutions.Featuring an industry-standard interface, the SIM900A delivers GSM/GPRS 900/1800MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. With a tiny configuration of 24mm x 24mm x 3 mm, SIM900A can fit almost all the space requirements in your applications, especially for slim and compact demand of design.

SKG13BL GPS Receiver Module with GPS antenna

General Description The SkyNav SKG13C is a complete GPS engine module that features super sensitivity, ultra low power and small form factor. The GPS signal is applied to the antenna input of module, and a complete serial data message with position, velocity and time information is presented at the serial interface with NMEA protocol or custom protocol. It is based on the high performance features of the MediaTek 3329 single-chip architecture, Its –165dBm tracking sensitivity extends positioning coverage into place like urban canyons and dense foliage environment where the GPS was not possible before. The small form factor and low power consumption make the module easy to integrate into portable device like PNDs, mobile phones, cameras and vehicle navigation systems. Applications  LBS (Location Based Service)  PND (Portable Navigation Device)  Vehicle navigation system  Mobile phone Features  Ultra high sensitivity: -165dBm  Extremely fast TTFF (Time To First Fix) at low signal level  Low power consumption: Typical 45mA@3.3V  NMEA-0183 compliant protocol or custom protocol  Operating voltage: 3.0V to 4.2V  Operating temperature range: -40 to 85℃  SMD type with stamp holes  Small form factor: 15x13x2.7mm  RoHS compliant (Lead-free)

ESP8266 serial ESP-01 WIFI Wireless Transceiver Module

ESP-01 ESP-8266 is an ideal choice for hobbyist to start experimenting with IOT. The dimension of this module is 25mm x 15mm, with simple pin connections (standard 2×4 pin headers), using serial TX/RX to send and receive Ethernet buffers, and similarly, using serial commands to query and change configurations of the WiFi module. ESP8266 ESP-01 Serial WIFI Transceiver Module is a cheap and easy way to connect to internet via WIFI to any microcontroller platforms like Arduino. You can use AT commands to connect to WiFi networks and open TCP/IP connections (without need to have TCP/IP stack running in microcontroller). The module(ESP-01) can work with AT command when used with Arduino, USB to TTL adaptor (FTDI USB module is recommended). Additional power supply might be needed to power upthe board.With GCC toochain and SDK availability opportunities with ESP8266 as a IOT device is endless.

ESP8266 ESP-03 WiFi Module

The ESP-03 is popular with more advanced users of the ESP8266 as it is the version of the module that has the most available GPIO pins broken out from the chip, which makes it great for more complex projects. Thanks to its on-board ceramic antenna, it's able to be smaller than the ESP-01 module.

ESP8266 Serial WIFI Wireless Transceiver Module ESP-07

ESP8266 ESP-12E Serial WiFi Wireless Transceiver SMD Module

ESP8266-12E is an enhanced version ESP8266-12, improve peripheral circuitry increases impedance matching, the signal output is better, whether it is stable or anti-jamming capability, have been greatly improved! For users before selecting the ESP-12, it does not matter even if the product has been made, enhanced version is fully compatible with previous firmware, the pin has added six IO ports on the basis of the ESP-12, SPI leads. ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.

ESP8266 ESP-12 Lua Nodemcu WIFI Dev Board Internet Of Things CP2102 Based

The NodeMcu is an open-source firmware and development kit that helps you to Prototype your IOT product within a few Lua script lines.

HM-10 BLE 4.0 Bluetooth Module

If you are in need of such a 4.0 BLE Bluetooth module, MCU can be set up,also can controlled by a remote Bluetooth device for setting,can transfer data, and can remotely control 10 PIO pins,so,the best choice is HM-10 bluetooth module. can replace HC-05, HC-06, HC-07 etc. Support Central and Peripheral mode switch, modify by AT commander. Support Remote control mode, remote device can control PIO pin or modify settings by AT commander when Connected. (such as Iphone4s/5 ipad, Note2 etc.) The Bluetooth UART RS232 serial Converter Module can easily transfer the UART data through the wireless Bluetooth, without complex PCB layout or deep knowledge in the Bluetooth software stack, you can combine this bluetooth module with your system:

SIM900A GSM/GPRS Modem Module - Talky Version

Ublox NEO-6M GPS Module Flight Control

The Ublox NEO-6M gps engine on this board is a quite good one, with high precision binary output. It has also high sensitivity for indoor applications. The gps module have a battery for power backup and EEprom for storing configuration settings. The antenna is connected to module through ufl cable which allow for flexibility in mounting the gps such that the antenna will always see the sky for best performance. This make it powerful to use with cars and other mobile applications. The Ublox gps module has serial TTL output, it has four pins:TX, RX, VCC and GND. You can download the u-center software for configuring the gps and changing the settings and much more. It is really good software.

NRF24L01+ 2.4GHz Antenna Wireless Transceiver Module

NRF24L01 with antenna V5.0 + PA + LNA wireless Module 8 Pin 1100 meters